DIY Pool Pump Cover Ideas: Step-By-Step Guide

A pool pump cover is important for your pool and should be treated carefully. If you do not have the proper knowledge, you could damage the pump or, even worse, destroy it.

Pool pump covers are often neglected. However, when one is not properly covered and fixed, it can create a lot of dirt and dust in the pool, which can harm your family’s health.

Making a pool pump cover by yourself can be challenging, but it’s pretty easy.

In this article, I will show you how easy it is to make a pool pump cover by yourself, with no expensive tools or skills needed, just like other DIY Pool Pump Cover Ideas.

How To Make Pool Pump Cover By Yourself?

The pool pump is one of the outdoor fixtures that should ideally be kept out of sight. The gear is hidden and shielded from the elements by this tiny home, which nonetheless permits simple access.

Wheelie bins or LPG cylinders are just two examples of additional objects that you may easily modify the proportions to fit.

Use primed H3-treated wood and a sliding compound mitre saw to cut the top edge of the rafters and bars at a 30-degree tilt to construct the stud walls and gable roof frames.

As there are only three pairs of rafters in this little structure, there is no need to add a ridge board; instead, reinforce the rafter connections with collar ties made from mending plates using a jigsaw equipped with a metal-cutting blade.

Buy raw rebated baltic pine weatherboards for the cladding and prime before assembly, but you can instead purchase primed H3-treated wood or prefabricated boards like Weathertex to save time.

Cut the galvanized corrugated roofing sheets to size using a nibbler or aviation shears, then combine them with tubular barge capping for a traditional country appearance.

Finish by painting the pump house and adding the hardware.

Using a 25mm chisel, cut out containers for 100mm stainless steel butt hinges on the doorjamb and the side of the door after the pump house has been fitted. Once hanging the door and securing the hinges are done, add a pad bolt.

After the external filler has dried, lightly sand the screw heads with 120-grit paper.

Apply metal paint after metal primer to the galvanized roof. Use two coats of exterior acrylic to the timber components to complete them.

Install Wall Frames

  • Use bugle screws to secure the studs that connect the base and upper plates.
  • Install screws after clamping the side frames between the front and back.
  • The door-side frame comprises two jambs, a top plate, and nothing else.

Prepare The Rafters

  • Mark 20mm-deep birdsmouth notches where a pair of rafters meet the top plates by clamping them together.
  • After marking and cutting the first notch, clamp all six rafters to flush their ends.

Create The Roof Frame

  • Screws and reduced mending plates are used as collar ties to join the rafter pairs.
  • Smoothly plane off the corner to level with the rafters, and then position the end purlins against the top plates.

Trim The Rafters

  • Using a jigsaw with a base plate set to 30º, snip the ends of the rafters by marking a plumb cut line 40mm from the frame’s outer edge with a builder’s square.
  • Screws are used to fasten the purlins to the top plates.

Fasten The Cladding

  • Screws should be used to clad the construction after turning it on its side.
  • As you continue, cut the gable pieces and mark them straight from the rafter profile.
  • Use an offcut to create the little top piece of the gable cladding.

Install Barges & Trim

  • Secure the barges using treated pine screws after clamping them into place with an 18mm overhang from the rafters.
  • Making use of a cladding offcut to balance the overhang, measure and trim the front and back trim pieces to fit.
  • The side trim pieces are still not added.

Create The Door Frame

  • Install screws after clamping the stiles between the rails.
  • Starting from the door, mark the diagonal bracing and cut it to the required size. Secure it by fastening it from the top of the bolt side to the bottom of the hinge side.
  • Shims are used to maintain equal spacing while you clamp the door into place.

Clad The Door

  • By screwing the boards to the door framework and the jambs, attach cladding to the entire door side.
  • By narrowing the gaps, you can free the door with a handsaw.
  • Before securing the highest board, begin the cut.

Install The Vent

  • Make the vent cutting with a jigsaw after drilling a beginning hole in the bottom gable using a 10mm twist bit.
  • Using construction adhesive, fasten the vent.
  • After attaching the side trim, cut the cladding flush with the barges using a handsaw.

Install The Tiedowns

  • Galvanized tie-downs are used to join the interior corners of the walls to the roof structure.
  • Using bugle screws, fasten the tiedown plates to the frame’s bottom surface.
  • For the roof, you’ll need two left-twist tie-downs and two right-twist tie-downs.

Secure The Capping

  • Screws are used to fasten the battens to the rafters.
  • Measure, mark, and then cut the barge capping from the roof framework to size using a hacksaw.
  • Using a clamp and roofing screws, fasten the barge capping to the rafters and barges.

Install The Roofing

  • After drawing a chalk line to mark the batten center lines, fasten the roofing sheets with screws, overlapping them by 1.5 corrugations.
  • Once the ridge cap has been installed, use a masonry bit to drill 8mm-diameter holes in the slab to anchor the frame.

Additional Tips While Making DIY Pool Pump Cover

  • Build rooms with high ceilings and include windows for adequate ventilation.
  • Ample space should be left for equipment maintenance and repairs, in addition to space for storing furnishings, pool supplies, and upkeep tools.
  • Even in completely closed buckets, chlorine chemicals will corrode the metal on pumps, filters, and heaters.
  • Heat pumps and heaters can’t be enclosed. Adequate air supply and exhaust ventilation are necessary for pool heaters.
  • Make sure the top is exposed to a clear sky if the sides are enclosed, or follow the manufacturer’s recommendations for proper venting.

Final Verdict

There are countless options for hiding your pool equipment, depending on your budget. Find out what works for you and your property, from simple and inexpensive to extravagant and expensive.

Don’t forget to plan, construct, or install something that fits your personal preferences and the climate in your area.

Are you someone who loves DIY projects? If yes, then I hope I have helped you with this article.

That’s all for today. Cheers!

FAQ

How can I cover the pool pump?

Installing a modest wall or screen to prevent the view and sounds of the pool pump and filter is the quickest and easiest way to conceal them.

If you are skilled with a saw, you might make your own DIY pool cover to conceal the pump following this article, or you could simply purchase vinyl privacy walls from most home improvement and garden centers.

Is a pump cover for a pool necessary?

The weather might seriously impact the elements that make up your pool heater and pump equipment.

Snow and ice, especially heavy rain and high gusts, must be kept away from the pump and heater. One of the main reasons for pool pump damage is the frozen lines and interior parts.

Please follow and like us: